Yamaha R6 complete motorbike carbs set up

**vtr_on_wye** · 18-09-2009, 08:59 PM

This is a full bike carb set up....

Bike carbs with ally inlet manifold to suit TU 8v engine
Distrubutor set up ready to bolt straight to head
Ignition coil and HT leads
Wiring loom, ready to plug straight into car loom (this does not make the rev counter work)
Two FSE fuel pressure regs one to bring down to 2 bar ish and the other just for fine adjustments for set up

This set up is ready to literally bolt straight onto your car...

£500 ono

Dan.

mark phillips · 19-09-2009, 09:36 PM

if you want a rev counter working with this just use AXGT clocks as they work off the coil

shmuliks87 · 20-09-2009, 07:36 AM

hi , i saw that to this carb' there is 4 red inj'
so this works like std carb without any ecu , and trottle bodies to
or it can be use only for trottle bodies ?

**jamesuk87** · 20-09-2009, 08:22 AM

those are purely carbs. The r6 throttle boddies look almost exactly the same but they have the injectors in them. These carbs will work without the ecu with the set up for sale and if set up properly with a nice cam will give a tasty boost in torque and power - not to mention the NOISE

**vtr_on_wye** · 20-09-2009, 10:13 AM

agreed

**7unner172** · 20-09-2009, 05:19 PM

will this fit straight onto my s1 1.3?

**freddy6868** · 20-09-2009, 05:26 PM

yeah

**vtr_on_wye** · 25-09-2009, 08:14 PM

bump...

**vtr_on_wye** · 01-10-2009, 08:49 PM

need these gone....will take sensible offers

monkey man · 26-10-2009, 04:19 PM

still got these mate?

**vtr_on_wye** · 26-10-2009, 06:56 PM

yeah carbs are still available!

joe_thompson · 28-10-2009, 03:25 PM

£200?

stugee · 28-10-2009, 04:19 PM

^

**aaron w** · 28-10-2009, 07:39 PM

will these run off the standard fuel pump? what other bits will i need? cheers

**vtr_on_wye** · 28-10-2009, 08:44 PM

yes mate run on a standard fuel pump..... you wont need anything else this is a plug and play kit!

**aaron w** · 29-10-2009, 05:41 PM

are they hard to set up?

dynofiend · 30-10-2009, 04:47 AM

How do you bolt the dizzy set up onto a head which doesnt have a dizzy on it as standard? Always wondered that...

Mankee · 30-10-2009, 08:22 AM

You just unbolt the cam end cover that the coil pack sits on and slap the new end cap on that has the dizzy on.

**Ian90** · 09-11-2009, 11:13 PM

are the carbs still up for sail.

**vtr_on_wye** · 10-11-2009, 07:42 AM

**sold**

18-09-2009, 08:59 PM	#1
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	Yamaha R6 complete motorbike carbs set up This is a full bike carb set up.... Bike carbs with ally inlet manifold to suit TU 8v engine Distrubutor set up ready to bolt straight to head Ignition coil and HT leads Wiring loom, ready to plug straight into car loom (this does not make the rev counter work) Two FSE fuel pressure regs one to bring down to 2 bar ish and the other just for fine adjustments for set up This set up is ready to literally bolt straight onto your car... £500 ono Dan.

20-09-2009, 08:22 AM	#4
jamesuk87 106 RALLYE REGISTER MEMBER Join Date: Jun 2008 Location: Sidcup - Holidays, Oxford Term time Posts: 1,258	those are purely carbs. The r6 throttle boddies look almost exactly the same but they have the injectors in them. These carbs will work without the ecu with the set up for sale and if set up properly with a nice cam will give a tasty boost in torque and power - not to mention the NOISE __________________ 165bhp Throttle boddied J4 - Bwaaaaaaaaarp

20-09-2009, 05:19 PM	#6
7unner172 NORTH EAST REGIONAL LEADER Join Date: Jul 2008 Location: newcastle Posts: 1,059	will this fit straight onto my s1 1.3? __________________ "If in doubt,flat out."™

20-09-2009, 05:26 PM	#7
freddy6868 106 RALLYE REGISTER MEMBER & SOUTH WALES GROUP LEADER Join Date: Jan 2008 Location: bridgend Posts: 3,538	yeah __________________ Engine:C2 VTS JP4 engine, JP4 cam covers, J4 cams, followers, valve springs and caps, Lightened flywheel, Pug racing gear linkages, heat wrapped 4-2-1 raceland manifold, 2" decat pugsport system, Pugsport group N engine mounts, powerflex exhaust mounts, 106 GTI airbox with K&N pannel filter, standard,S2 gearbox, 153bhp @ 7,310rpm 112ft/lbs @ 6,739rpm Interior:Standard interior apart from Sparco Evo bucket seats, Sabbelt 3" 6 point harnesses Body:Brand new S1 vinals all round, red FG bonnet Chassis:Poly bushed diesel spec wishbones, lowered on Gaz coilovers on the front adjustable height -40mm-90mm, S1 rear beam poly bushed and lowered 45mm with Rear Gaz rear dampers, S2 steelies, Brakes:Front brakes:Godspeed brake set up consisting of Brembo Max disks (on order), standard calipers and mintex 1155 pads with braided flexi pipes. Rear brakes: standard S1 drums and shoes with goodridge flexi pipes SEX, PUGS AND ROCK 'N' ROLL

30-10-2009, 04:47 AM	#17
dynofiend MEMBER & FORUM MODERATOR Join Date: Jan 2004 Location: New Zealand Posts: 14,994	How do you bolt the dizzy set up onto a head which doesnt have a dizzy on it as standard? Always wondered that... __________________

19-09-2009, 09:36 PM	#2
mark phillips REGISTERED FORUM USER Join Date: Jul 2009 Location: bridgend Posts: 12	if you want a rev counter working with this just use AXGT clocks as they work off the coil

20-09-2009, 07:36 AM	#3
shmuliks87 SOON TO BE FREELOADER Join Date: Sep 2006 Location: us Posts: 91	hi , i saw that to this carb' there is 4 red inj' so this works like std carb without any ecu , and trottle bodies to or it can be use only for trottle bodies ?

20-09-2009, 10:13 AM	#5
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	agreed

25-09-2009, 08:14 PM	#8
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	bump...

01-10-2009, 08:49 PM	#9
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	need these gone....will take sensible offers

26-10-2009, 04:19 PM	#10
monkey man FREELOADER! 100+ posts still not joined :-( Join Date: Apr 2009 Location: corwen Posts: 100	still got these mate?

26-10-2009, 06:56 PM	#11
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	yeah carbs are still available!

28-10-2009, 03:25 PM	#12
joe_thompson REGISTERED FORUM USER Join Date: Sep 2009 Location: stoke Posts: 22	£200?

28-10-2009, 04:19 PM	#13
stugee RECENTLY EXPIRED Join Date: Sep 2007 Location: West Lothian Posts: 2,033	^

28-10-2009, 07:39 PM	#14
aaron w 106 RALLYE REGISTER MEMBER Join Date: Feb 2005 Location: hants Posts: 1,123	will these run off the standard fuel pump? what other bits will i need? cheers

28-10-2009, 08:44 PM	#15
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	yes mate run on a standard fuel pump..... you wont need anything else this is a plug and play kit!

29-10-2009, 05:41 PM	#16
aaron w 106 RALLYE REGISTER MEMBER Join Date: Feb 2005 Location: hants Posts: 1,123	are they hard to set up?

30-10-2009, 08:22 AM	#18
Mankee FO(cate)RUM MODERA7OR Join Date: Sep 2004 Location: P*sswich aka Ipswich Posts: 8,709	You just unbolt the cam end cover that the coil pack sits on and slap the new end cap on that has the dizzy on. __________________ Stuff for sale on Fotki and here Javelin Trackdays: 1/8: Barkston Heath, Lincolnshire 7/8: Woodbridge, Suffolk 10/8: Cadwell Park, Lincolnshire (evening session) 28/8: Croft, Yorkshire September: ZOMG, Tour Britannia! Oulton Park, Angelsey, Mallory Park

09-11-2009, 11:13 PM	#19
Ian90 106 RALLYE REGISTER MEMBER Join Date: Nov 2009 Location: Cumbria Posts: 27	are the carbs still up for sail.

10-11-2009, 07:42 AM	#20
vtr_on_wye 106 RALLYE REGISTER MEMBER Join Date: Oct 2006 Location: Ross-on-Wye Posts: 491	sold

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode